SAG-100WM devices are suitable for connecting small-scale private networks to Alibaba Cloud. This topic describes SAG-100WM devices.

Specifications

SAG-100WM provides two device types that have different specifications. The exterior and sizes of these two device types are different, but the supported features are the same. For more information, see Features of Smart Access Gateway devices.

  • Type 1 Size: 180 mm × 110 mm × 30 mm
    • Front panel
    • I/O panel
  • Type 2 Size: 240 mm × 148 mm × 28 mm
    • Front panelFront panel-22
    • Side panelSide panel-22
    • I/O panelI/O panel-22
Property Type 1 Type 2
Performance (tested in 512 bytes) The bandwidth for encrypted private connections can reach 50 Mbit/s The bandwidth for encrypted private connections can reach 50 Mbit/s
Working environments Suitable for indoor environments with no fans attached Suitable for indoor environments with no fans attached
Size 180 mm*110 mm*30 mm 240 mm*148 mm*28 mm
Working temperature 0℃ to 45℃ 0℃ to 45℃
Storage temperature -40℃ to 70℃ -20℃ to 70℃
Power DC 12 V DC 12 V
Power consumption 12 W 12 W
Network ports Two GE/FE RJ45 WAN ports
Note One of the WAN ports is in bridge mode. Therefore, only one WAN port is available.
One GE/FE RJ45 WAN port
Three GE/FE RJ45 WAN ports One WAN/LAN reusable port (port 2)
Three GE/FE RJ45 WAN ports
WIFI
  • 2.4 GHz and supports IEEE 802.11 b/g/n
  • Supports at most 20 terminals
  • Signal covers 100 square meters
  • 2.4 GHz and supports IEEE 802.11 b/g/n
  • Supports at most 20 terminals
  • Signal covers 100 square meters
4G LTE in mainland China 4G network provided by China Unicom, China Telecom, and China Mobile 4G network provided by China Unicom, China Telecom, and China Mobile
USB USB 2.0 USB 2.0

Device panels

The following tables describe the device panels. "√" indicates "supported" while "×" indicates "not supported".

  • Front panel: provides five LED indicator lights, as described in the following table.
    Indicator Status SAG-100WM specification
    Type 1 Type 2
    LTE Indicates the connection status of the device:
    • On or off: an error occurred.
    • Flashing: working as expected.
    WAN Indicates the Ethernet status:
    • On or off: an error occurred.
    • Flashing: working as expected.
    ×
    WIFI Indicates the Wi-Fi connection status:
    • On or off: an error occurred.
    • Flashing: working as expected.
    RUN/SYS Indicates the power status:
    • On or off: an error occurred.
    • Flashing: working as expected.
    CLOUD Indicates whether the device is connected to Alibaba Cloud:
    • On: connected to Cloud Connect Network (CCN).
    • Flashing: restoring the system or restoring to default settings.
    • Off: not connected to CCN.
    PWR Indicates whether the device is powered on:
    • On: powered on.
    • Off: not powered on.
    ×
    Descriptions of status indicator lights
    RJ45 yellow light Indicates the working mode of the network interface controller (NIC):
    • On: Ethernet port working in 1000Base-T mode.
    • Off: Ethernet port working in 10/100Base-T mode.
    RJ45 green light Indicates the connection status and speed of the NIC:
    • On: Ethernet connected.
    • Flashing: transferring data.
    • Off: Ethernet not connected.
  • I/O panel: provides one reset button, one subscriber identity module (SIM) slot, one USB port, two WAN ports, three LAN ports, and one power inlet.
    Note The SIM card slot of a Type 2 device is on the side of the device.
    • The reset button

      To restore the device to the default settings, keep the device powered on, and press and hold the reset button for three seconds. Then, the device is automatically restarted and restored to the default settings.

    • The SIM card slot

      You can directly insert only a Mini-SIM card into the slot. A Micro-SIM or Nano-SIM card cannot be directly inserted into the slot. If you need to use a Micro-SIM or Nano-SIM card, you must use a card frame adapter instead of a card sleeve adapter. The card may be stuck in the slot if you use a card sleeve adapter.

      SAG-100WM devices support Mini-SIM, Micro-SIM, and Nano-SIM cards. You must use a card frame adapter if you want to use a Micro-SIM or Nano-SIM card.

      Mini-SIM, Micro-SIM, and Nano-SIM cards are known as 2FF, 3FF, and 4FF cards, as shown in the following figure.
    • The USB port

      4G USB is not supported for access to the Internet.

    • The WAN ports

      The WAN ports support Internet access, Source Network Address Translation (SNAT), dynamic IP addresses, static IP addresses, and Point-to-Point Protocol over Ethernet (PPPoE).

    • The LAN ports

      The LAN ports can be connected to on-premises clients and allow you to configure routes and connect the device to switches.

    • WAN or LAN reusable port

      The WAN or LAN reusable port can be used as a WAN port or a LAN port.

      Note
      The default port type of the reusable port, which is determined by the version of the SAG-100WM device.
      • If the version of your SAG-100WM device is 1.0.x, the WAN or LAN reusable port functions as a LAN port by default.
      • If the version of your SAG-100WM device is 2.0.x, the WAN or LAN reusable port functions as a WAN port by default.
    • The DC power inlet

      The power inlet is on the I/O panel. The power supply must be 12V DC.

      Note Use the original power cord.

Device accessories

After you purchase an SAG device in the SAG console, you will receive an SAG-100WM device and the following accessories:
  • Type 1
    • A power cord
    • A network cable
  • Type 2
    • A power cord
    • A network cable
    • Two LTE antennas
Note Check the SAG-100WM device and its accessories. If an accessory is missing or damaged, contact Alibaba Cloud after-sales service. The SAG-100WM device is selected randomly from one of the two types.